Home        Main menu

This page last updated: October 27, 2010

WK badges and nameplates

Badge removal and installation

Badge Location Part # MSRP* Model Year(s)
WK Boston Acoustics badge Speakers (front door) 68024539AA $ 9.00 2007-2010
WK CRD badge Liftgate 55157095AC $27.00 2007-2008
WK 3.0L badge Liftgate (right side) 68038123AA $29.95 2007-2008
WK Flex Fuel badge Liftgate (right side) 55372784AA $39.70 2007-2010
WK 4x4 badge Liftgate (left side) 55157091AA
superseded by:


$28.85 2005-2010
WK 5.7L badge Liftgate (right side) 55157092AA
superseded by:


$26.10 2005
Hemi badge Liftgate (right side) 55079103AA $37.95 2007-2010
WK 5.7L Hemi badge Liftgate (right side, combo set)

(Note: The "5.7L" portion of "5.7L HEMI" badge was deleted on all models built on or after June 29, 2006)

55157454AA $44.25 2006
WK Jeep badge, hood Hood 55157088AA
superseded by:


$42.35 2005-2010
WK Jeep badge Liftgate (center) 55157089AA
superseded by:


$42.35 2005-2010
WK Laredo badge Liftgate (left side) 55157303AB
superseded by:


$22.35 2005-2010
WK Limited badge Liftgate (left side) 55157090AA
superseded by:


$28.85 2005-2010
WK North Edition badge Door (left side) 5113554AA $57.70 2008-2010
WK Overland badge Liftgate 55157358AA $37.35 2006-2010
WK Rocky Mountain Door (front) 55079387AA $23.50 2005, 2007-2009
WK 65th anniversary badge Fender (front) 55373001AA $21.75 2006
WK S-Limited badge Liftgate 55079385AA $25.25 2008-2010
SRT8 badge Liftgate (right side, 5-7/8" x 9/16") 5029893AA
superseded by:


$68.95 2006-2010
WK Trail Rated badgeFront fender, left side only
(heavier and more detailed than 2004 version)

NOTE: The following Grand Cherokees are "NOT" Trail Rated:

1. All 3.7L 4-wheel drive and 2-wheel drive WK's are NOT Trail Rated.

2. All 4.7L and 5.7L 2-wheel drive WK's are NOT Trail Rated.

superseded by:


$28.60 2005-2010
NOTE: Prices listed are for reference purposes only and may vary by dealer. Prices are current as of November, 2010. Parts are not available from this web site.

Exterior badge removal

NOTE: Exterior nameplates are attached to body panels with adhesive tape.

1. Apply a length of masking tape on the body, parallel to the top or bottom edge of the nameplate to use as a guide, if necessary. An additional piece of tape can also be placed on the left or right side of the badge for more accurate alignment when reinstalling.

2. If temperature is below 21C (70F) warm emblem with a heat lamp or gun. Do not exceed 52C (120F) when heating emblem. A hair dryer may also be used.

3. Insert a plastic trim stick or a hard wood wedge behind the emblem to separate the adhesive backing from the body. A short length of fishing line can also be used.

4. Clean adhesive residue from body with MOPAR Super Clean solvent or equivalent.


1. Remove protective cover from adhesive tape on back of emblem.

2. Position emblem properly on body.

3. Press emblem firmly to body with palm of hand.

4. If temperature is below 21C (70F) warm emblem with a heat lamp or gun to assure adhesion. Do not exceed 52C (120F) when heating emblem.

WKJeeps.com website Premier Sponsor
Discount Jeep Parts and Accessories
shipped worldwide

Home     Main menu